PowerCenter Minitower 180 Specifikace Strana 1

CONFIDENTIAL 1 PowerCenter ª ProPowerCenter ª Pro Certification ModuleCertification Module PowerCenter Pro Minitower 180/210 PowerCenter ª Pro NT

CONFIDENTIAL 10 in the slot. Slide the contacts straight into the slot and make sure the contacts are firmly seated. ( see Figure 5: Installing RAM

CONFIDENTIAL11Removing the CPU1. Remove the chassis cover (refer to Chassis Cover Removal/Installation on page 6).2. Place the unit on its side with t

CONFIDENTIAL122. Lower the CPU card squarely into the slot so that the notch in the CPU card lines up with the notch in the slot. Slide the contacts s

CONFIDENTIAL13Removing the Cache1. Remove the chassis cover. (refer to Chassis Cover Removal/Installation on page 6).2. Place the unit on its side wit

CONFIDENTIAL14NNNNooootttteeee:::: Before you install any expansion cards, be sure that the combined power consumption of theexpansion cards does not

CONFIDENTIAL154. Hold the PCI card (contacts facing down) with one hand at each end. Notice that there is a notch in the contact edge of the PCI card.

CONFIDENTIAL16Removing the PCI Riser Card1. Remove the chassis cover (refer to Chassis Cover Removal/Installation on page 6).2. Locate the riser card

CONFIDENTIAL17Installing the PCI Riser Card1. Lower the PCI riser card squarely into the PCI slot so that the notch in the PCI card lines up with the

CONFIDENTIAL18Removing the Adaptec SCSI Card1. Remove the chassis cover (refer to Chassis Cover Removal/Installation on page 6).2. Disconnect any cabl

CONFIDENTIAL194. Hold the Adaptec SCSI card (contacts facing down) with one hand at each end. Notice that there is a notch in the contact edge of the

CONFIDENTIAL 2 CPU PowerPC 604e at 180MHz or 210MHz Main Logic Board Catalyst (Comparable to a Macintosh 7200) CPU Upgrade Available via daught

CONFIDENTIAL206. Connect the UltraSCSI cable to the Adaptec SCSI card.7. Reset the CUDA (refer to CUDA Reset on page 4).8. Replace the chassis cover

CONFIDENTIAL21Removing the Floppy Disk Drive1. Remove the chassis cover (refer to Chassis Cover Removal/Installation on page 6).2. Disconnect the cabl

CONFIDENTIAL224. Replace the screws that attach the floppy disk drive cage to the5.25-inch drive cage and the front of the chassis. 5. Reconnect the c

CONFIDENTIAL23Removing the 3.5-inch Drive1. Remove the chassis cover (refer to Chassis Cover Removal/Installation on page 6).2. Remove all cables from

CONFIDENTIAL24Removing 5.25-inch Drives1. Remove the chassis cover (refer to Chassis Cover Removal/Installation on page 6).2. Disconnect all cables th

CONFIDENTIAL253. Replace the screws that secure the drive.4. Reset the CUDA (refer to CUDA Reset on page 4).5. Install the chassis cover (refer to Cha

CONFIDENTIAL26Removing the MLB (Main Logic Board)1. Remove the chassis cover (refer to Chassis Cover Removal/Installation on page 6). 2. Place the com

CONFIDENTIAL27Installing the MLB1. Lower the MLB into the chassis at an angle. Lay the board flat and align the mounting holes with the posts.2. Repla

CONFIDENTIAL28Removing the Power Supply1. Remove the chassis cover. (refer to Chassis Cover Removal/Installation on page 6). 2. Disconnect the logic b

CONFIDENTIAL29Installing Power Supply 1. Slide the power supply into place, making sure that it is seated properly.2. Secure the power supply with th

CONFIDENTIAL 3 To ensure your personal safety as well as prevent unnecessary damage to the computer, please follow all safety precautions when perfor

CONFIDENTIAL30This module was written and designed by: Michael Scott Clay.Additional contributions by:Shane NestleJeff PryorEdited byMark WoodLaurie

CONFIDENTIAL 4 The CUDA Reset button is a small red button located on the Main Logic Board. Depressing this button resets the CUDA Microcontroller Ch

CONFIDENTIAL 5MLB DIAGRAMMLB DIAGRAMMLB DiagramMLB

CONFIDENTIAL 6 Removing the Chassis Cover 1. Shut down the computer and turn off all external devices. If you do not have a grounding strap, leave t

CONFIDENTIAL 7 Removing the Front Bezel Cover 1. Remove the chassis cover (refer to Chassis Cover Removal/Installation on page 6). 1. Remove the

CONFIDENTIAL 8 Installing the Front Bezel 1. Connect the switch and speaker wires to their respective ports on the main logic board. 2. Screw the be

CONFIDENTIAL 9 NNNNooootttteeee:::: All DIMMs must be 168-pin, fast-paged mode, 60-nanosecond RAM access time or faster. ThePowerCenter has four DI